Demo site by Demand & ConvertWant a website like this? Get a free website + a 60-day free Local SEO trial.Get my free website

Author: Steve Chhay

Why LED Bulbs Flicker on a Dimmer, and How to Fix It

You change your old bulbs for LEDs and the lights start to flicker, buzz or glow faintly when they should be off. The bulbs are probably fine. The usual cause is a mismatch between the bulbs and the dimmer on the wall. Here is how to work out what is going on.

Why the old dimmer struggles

Older dimmers were made for incandescent bulbs, which draw a lot of power. An LED bulb gives the same light with a small fraction of that power. Many older dimmers need a minimum load to work properly, and a few LED bulbs may not reach it. The dimmer then behaves in odd ways.

What a mismatch looks like

  • Flickering, mostly at low settings
  • A buzz or hum from the bulbs or from the dimmer
  • Lights that jump from off to fairly bright with nothing in between
  • Lights that cut out before the slider reaches the bottom
  • A faint glow that stays when the dimmer is off

Check the bulbs first

Not every LED bulb can be dimmed. Look at the base of the bulb or the box for the word dimmable. A bulb that is not made for dimming will flicker or fail early on any dimmer, and the fix is simply a different bulb.

Use the same bulb in every socket on one dimmer. Mixing brands, or mixing LED bulbs with older types, often causes uneven dimming.

Then check the dimmer

Look for a dimmer that is made for LED loads. The packaging will say so. Many bulb and dimmer makers also publish lists of products that have been tested together, and it is worth a look before you buy.

Pay attention to the rating. A dimmer has one limit for incandescent bulbs and a lower limit for LEDs. Add up the watts of all the bulbs it controls and stay within the LED figure.

The small adjustment many people miss

Many LED dimmers have a small dial or lever hidden behind the wall plate or on the side of the switch. It sets the lowest level the dimmer will go to. If your lights flicker or drop out at the bottom of the range, raising this setting a little often cures it. The instructions that came with the dimmer explain how.

Switches at both ends of a hall or stair

When two switches control the same lights, the dimmer has to be a type made for that arrangement, and normally only one of the two positions gets the dimmer. Putting a standard dimmer at each end does not work.

Smart dimmers

Many smart dimmers need a neutral wire in the switch box. Some older houses do not have one there. Find this out before you buy, because it decides which models you can use.

When the dimmer is not the cause

Sometimes flickering has nothing to do with dimming. Take note if any of these are true:

  • Lights flicker on circuits with no dimmer at all
  • Lights across the whole house dim when a large appliance starts
  • The dimmer or its plate feels hot, not just slightly warm
  • You hear crackling, or smell something burning, at the switch

These point to a loose connection or a problem at the panel or the service to the house. Stop using the switch, turn off its breaker if you can do so safely and call an electrician.

A simple order to try things in

  • Confirm the bulbs are dimmable and all the same
  • Check the dimmer is made for LED bulbs and is within its rating
  • Adjust the low-end setting if the dimmer has one
  • If it still flickers, have the wiring checked

If you would like help choosing and fitting the right dimmers, call Switchplate Home Electric. We test the bulbs and dimmers together, replace what does not match and leave the plates straight.

How to Label Your Breaker Panel in One Afternoon

If the labels in your breaker panel are faded, wrong or missing, you can fix that yourself. You do not need to take anything apart. You only need to flip breakers, walk the house and write things down. Here is a method that works.

What you need

  • A helper, or a phone call between two phones in the house
  • A small lamp, a night light or a plug-in outlet tester
  • A notepad and a pen
  • A flashlight, since the lights near the panel may go off
  • Numbered stickers or a fine marker

Before you start

Save your work and shut down computers. Let everyone in the house know the power will go on and off. If anyone relies on powered medical equipment, plan around it or leave this job to an electrician.

Open the panel door only. Never remove the metal cover that the breakers poke through. Everything you need for this job is on the outside of that cover.

Step 1: Number the breakers

Many panels have numbers stamped next to each slot, odd on the left and even on the right. If yours does not, add your own with stickers. Write the same numbers down the side of your notepad.

Step 2: Start with the easy ones

Large appliances usually have a breaker of their own. Wide breakers that take up two slots normally serve things like the range, the dryer, the air conditioner or an electric water heater. Turn one off, see which appliance has lost power, write it down and turn it back on.

Step 3: Work through the rest

Turn every light in the house on. Then switch off one breaker. Your helper walks the house and notes which lights went out. Next they test the outlets in those rooms and the rooms next to them with the lamp or tester, top and bottom of each one. Write down what you find, then turn the breaker back on and move to the next.

Go slowly. One breaker often serves parts of two or three rooms, and one room is often split between two breakers.

Step 4: Hunt for the leftovers

When you finish, some things will not be on your list. Check these places:

  • Outdoor outlets and porch lights
  • The garage, including the door opener
  • The furnace, sump pump and doorbell transformer
  • Bathroom fans and the outlets by the sinks
  • The dishwasher, the disposal and the refrigerator
  • Attic and crawl space lights
  • Smoke alarms that are wired in

Step 5: Write labels that will still make sense later

Describe places, not people. A label that says north bedroom outlets will still be right after the room changes hands. A label that says Sam’s room will not. Be specific: kitchen counter outlets left of sink is better than kitchen.

Type or print the list neatly, fix it inside the panel door and keep a copy with your house papers. Add the date.

What to do if something seems off

Mapping a panel sometimes turns up surprises. Call an electrician if you notice any of the following:

  • A breaker that feels hot, buzzes or will not stay on
  • Rust, water marks or a burning smell at the panel
  • A breaker that appears to control nothing at all
  • An outlet or light that stays on no matter which single breaker you turn off
  • One breaker that shuts off most of the house

None of these should be fixed by opening the panel yourself.

Why it is worth the afternoon

A labeled panel saves time whenever work is done on the house. More than that, it means anyone at home can find the right breaker quickly when something smells hot or a pipe leaks near an outlet.

If you would like it done for you, or you ran into one of the surprises above, call Switchplate Home Electric. We map panels, type the directory and explain anything that needs attention.

Not sure which breaker does what?

Tell us about your panel and we will help you sort it out.

Request a Visit(614) 555-0129 or send us the details
Call